Home > News information

News information

Choosing 128MB Storage for Firmware and Assets, W25Q01JVZEIQ with PY25Q01GHB as Second Source

1Gbit, or 128MB, is the divider between a firmware image and a firmware image plus its assets. Code keeps growing, and a main image, a backup image, and a voice resource pack do not fit in 16MB. The 16MB generation ran out fast: two 8MB images consumed the whole chip, bootloader and parameter area had nowhere to live, and compressing each image to 7MB meant one interrupted upgrade sent the unit back to the factory.

At the same capacity, two device families sit side by side: SPI NOR FLASH and SPI NAND FLASH. The capacity is the same, but switching from NOR to NAND only makes sense in very specific situations. With NAND pricing where it is today, NOR often comes out lower on total cost, which is why so many designs settle on a part like the Winbond W25Q01JVZEIQ. This article explains that part first, then covers how to move to the Puya PY25Q01GHB when Winbond pricing and supply tighten.

Why 1Gbit rarely moves to SPI NAND FLASH

SPI NOR FLASH has three advantages at 128MB that are hard to replace. First, byte-level random access, so code can run in place from the flash (XIP) without being copied to RAM, which keeps boot fast. Second, every block is good from the factory, so there is no bad-block table to maintain. Third, the software stack is simple: a block device is read directly and the file system treats it as ordinary storage. What this capacity band needs is exactly fast boot, code that executes in place, and no bad blocks, and all three land on NOR's strengths.

SPI NAND FLASH competes on cost per bit, and that advantage only opens up at larger capacities. The price is three pieces of software: ECC, because NAND is allowed to ship with bad blocks and every read and write must be checked; bad-block management; and an FTL, the layer that maps bad blocks and levels wear. With NAND pricing where it is now, unit prices at 1Gbit are already close, and once development and validation of that software is counted, NOR is the lower total cost, saving two to three months of engineering. NAND only wins when a design writes large sequential files, expects capacity to keep climbing, and already has an FTL team. For 128MB, the default answer is NOR, and the Winbond W25Q01JVZEIQ is a common starting point.

W25Q01JVZEIQ is a common choice at 1Gbit NOR FLASH

The W25Q01JVZEIQ holds 1Gb, 128MB. Internally it is built from two 512Mb dies, but to the host it is one continuous 128MB space, so the driver does not stitch two chips together. The interface covers standard, dual, and quad SPI, up to 133MHz in quad mode, roughly 532Mbps. Supply is 2.7V to 3.6V, and full 133MHz operation needs 3.0V or more. Operating temperature is -40°C to +85°C, and the package is WSON-8 at 8.0 x 6.0mm. Quad mode is enabled from the factory, so a host that switches to quad can use it immediately. The part has no hardware reset pin; reset is done with two fixed commands and returns the device to its power-up state in about 30µs.

Two things belong in the design review early. The first is address length. 128MB exceeds the 16MB that a traditional 3-byte address can reach, and the part ships in 3-byte mode. Once an address crosses 16MB it wraps to the start, and the read returns old data from the beginning of the array. The symptom looks like this: the write reported success, but the read gives back the previous contents. One fixed command after power-up switches to 4-byte addressing. Note that a soft reset returns the device to the factory default, so the command has to be issued again after every reset, and the upgrade flow must not miss it. The second is the busy state of the two internal dies. The busy flag reports only the die currently being accessed; the other die may still be working. Allow about 200µs between operations that cross to the other die, otherwise occasional verify failures appear.

ParameterValue
Ordering part numberW25Q01JVZEIQ
Density1Gb (128MB), two 512Mb dies with linear addressing
InterfaceStandard / Dual / Quad SPI
Max clock133MHz (532Mbps equivalent in quad)
Supply voltage2.7V to 3.6V (3.0V to 3.6V for full 133MHz)
Operating temperature-40°C to +85°C
PackageWSON-8, 8.0 x 6.0mm
Endurance100,000 program/erase cycles, 20-year retention

When Winbond is tight, PY25Q01GHB can take over

Winbond W25Q01JVZEIQ pricing and supply are both tight right now. The Puya PY25Q01GHB is the same 1Gbit SPI NOR FLASH class, 2.7V to 3.6V, -40°C to +85°C, supporting standard SPI, dual, quad, QPI, and DTR. Functionally the grades line up, and the replacement effort sits in the package and the driver.

The package means a board change. The PY25Q01GHB comes in SOP16 300mil and TFBGA-24 with 5x5 and 4x6 ball arrays, across four ordering part numbers. The Winbond part is WSON-8 at 8x6mm and shares no footprint with any of them, so the PCB has to change; this is not a pin-to-pin swap. The driver has three checks. Keep address variables 32 bits wide and delete masks such as addr & 0xFFFFFF. Split page programs at 256-byte boundaries so a single command never crosses a page. The status register bit order for busy, write-enable latch, and block protect matches Winbond, but the quad-enable and HOLD/RST shared bits must be reviewed item by item; HOLD# can be configured as RESET#, which is a neat way to add a reset pin to a design that has none. Re-issue the write-enable command before every page program and erase, since the latch clears itself when the operation completes. Write timing also needs recalculating: a 24MB main image means 384 64KB block erases plus 98,304 page programs, about a minute and a half at typical values. Production takt planning has to allow several times that if the datasheet maximums are used, and an OTA timeout set from typical values will declare a false failure.

ParameterValue
Ordering part numbersPY25Q01GHB-SMH-IT / -SMH-IR / -TFH-IY / -TBH-IY
Density1Gbit (128MB)
InterfaceSPI / Dual / Quad / QPI, DTR supported
Supply voltage2.7V to 3.6V
Operating temperature-40°C to +85°C
Page / sector / block256B / 4KB / 32KB, 64KB
Endurance100,000 cycles, 20-year retention
Standby / deep power-down80µA / 4µA
PackageSOP16 300mil, TFBGA-24 (5x5, 4x6)

Sourcing view

At 1Gbit NOR, Winbond, Puya, GigaDevice, and ISSI all have parts, and a second source is about more than price: when one supplier stretches lead times, production keeps running. When qualifying the Puya part, lock a single package version, because mixing 5x5 and 4x6 ball arrays on one line causes placement offset. Samples and volume timing can be scheduled to the project milestones.

Samples, volume supply, and complete datasheets for both the W25Q01JVZEIQ and the PY25Q01GHB are available from Shenzhen Manduic Technology Co., Ltd. We are an authorized distributor of Winbond, and we can also source samples and datasheets for the Puya part, with package changes and address-mode checks handled together.

For samples, datasheets, adaptation support, or technical questions, reach us through the channels below:

Tel: 150-1290-5940

Email: sales@manduic.com

Website: www.manduic.com