Home > Product Center > Analog IC

The power path between the battery and the load. Low-dropout linear regulators from Hypower and wide-input DC-DC converters, from a 300mA part in a 1×1mm DFN to a 3A step-down in ESOP8.

Two sub-lines, twelve Hypower LDO series and 44 DC-DC part numbers, with datasheets, samples and fast quotes.

Sub-linesLDO + DC-DC
Linear300mA – 1.5A
Step-downup to 3A
Vin1.6V – 36V
Packagefrom DFN 1×1mm

Why Analog Power

⚖LDO or Step-down

A linear regulator is the shortest path to a quiet rail, with no inductor and no switching noise. A step-down converter wins once the input-to-output gap and the load current push the linear part past its thermal budget.

▣The Package Is a Spec

The Hypower line puts 300mA to 1A regulators in DFN 1×1mm and TDFN 1×1mm, so the rail sits next to the sensor or the MCU instead of across the board. The same silicon is also offered in SOT23, SOT89-3 and SOT223 where dissipation matters more than area.

◈Fixed, Adjustable, Wide Input

HP6012 gives both an adjustable 0.6–5V output and fixed 0.8–3.6V options. AWL5963 ships as 1.8V, 2.5V, 3.3V and ADJ versions. Where the bus is 12V or 24V, AWK6613 takes 3–36V in and delivers 3A at 400kHz.

Product Line

Two sub-lines cover the power path. Hypower for ultra-small linear rails, DC-DC for higher current and wide-input step-down. Click a line to view its full listing.

ULTRA-SMALL DFN 1×1 · 300mA – 1A
Hypower LDO

Twelve low-dropout series from 300mA to 1A. HP6011 to HP6022 sit in DFN 1×1mm and TDFN 1×1mm on 1.6–6.5V input, with 1.2–3.6V fixed outputs; HP1117 and HP6050 cover the 1A end in SOT223, TO252, SOT89-3 and DFN 1.2×1.6.

View Hypower LDO series →
1.5A LDO + 3A BUCK
DCDC

44 part numbers over two families. AWL5963 regulates 2.3–20V down at 1.5A in SOP8L, SOT223-3 and TO263-5. AWK6613 steps 3–36V down at 3A and 400kHz in ESOP8.

View DCDC parts
Need a part number that is not listed? Send us the rail, the load and the package — we will cross-reference the Hypower and DC-DC families and reply with datasheets and pricing.

Typical Applications

◐Wearables and TWS

A 1×1mm rail placed beside the MCU on boards measured in millimetres, with the load current kept in the hundreds of milliamps.

⚡Battery-Powered IoT

Single-cell lithium and 3.3V systems regulated straight from a 1.6–6.5V input, keeping the part count and the quiescent budget low.

⌂Smart Home Devices

Always-on rails for control panels and connected appliances, where a quiet output keeps the radio and the analog front end clean.

▤Meters and Instruments

A 3–36V wide-input step-down that survives a 12V or 24V bus and still holds regulation through the brownout at the end of a battery cycle.

⚙Industrial Control

A 400kHz converter for 24V rails feeding relays, drivers and the logic supply, sized at 3A in ESOP8 for the thermal headroom.

✦Sensor and MCU Supply

A linear post-regulator after a switching stage, so the sensor, the reference and the MCU core sit on rails free of switching ripple.

Analog Power FAQ

Q1
When should I use an LDO instead of a DC-DC converter?

Use a linear regulator when the output is close to the input, the current is modest, or the rail feeds an analog or RF block that cannot tolerate switching ripple. Use a converter when the voltage gap multiplied by the load current would exceed what the package can dissipate.

Q2
How do I get 3.3V from a single lithium cell?

A single cell spans roughly 3.0–4.2V, so a 3.3V rail needs a part that regulates both above and below the set point. A buck-boost or a low-dropout part with enough headroom at the low end of the discharge curve is the usual answer; tell us the load current and we will point at the right family.

Q3
What input and output ranges are covered?

The linear families take 1.6–6.5V in with 1.2–3.6V fixed outputs, or 0.6–5V adjustable on HP6012. AWL5963 handles 2.3–20V at 1.5A, and the AWK6613 buck accepts 3–36V at 3A.

Q4
Which packages can I choose from?

On the Hypower side, DFN 1×1-4 and TDFN 1×1-4 for the smallest boards, SOT23-3, SOT23-5, SOT89-3 and SOT223-3 for conventional layouts, plus DFN 1.2×1.6-8 on HP6050. DC-DC parts ship in SOP8L, ESOP8, TO252 and TO263-5, where the larger tab carries the dissipation.

Q5
How do I get a datasheet or a sample?

Click a sub-line above to browse part numbers, or send us the input range, the output voltage and current, the package and the temperature grade. We reply with datasheets, samples and pricing.

Related Products

Every rail on a board needs the rest of the system around it. These categories pair naturally with analog power.

The load being regulated
Microcontroller

MCUs whose core and IO rails are fed from these regulators, from Artery, YunTu and Cmsemicon.

View MCU →
Code storage
NOR Flash

Firmware and boot code, powered from the same 3.3V or 1.8V rail as the MCU.

View NOR Flash →
Working memory
RAM Memory

SRAM and pSRAM for code shadowing and frame buffers, sensitive to the rail you regulate.

View RAM Memory →
Timing reference
Oscillator

Crystals and oscillators for the same clock tree, from Hosonic, EPSON, NDK and SiTime.

View Oscillator →
Clean analog front end
Sensor

Magnetic and current sensors that need a quiet supply, from CONNTEK, Magntek and Allegro.

View Sensor →
Full catalog
Product Center

Browse all memory, oscillator, MCU, analog and sensor lines in one place.

View Product Center →

Request a Quote

Tell us the input range, the output voltage and current, the package and the quantity. Our team replies with pricing, stock and datasheets within one business day.

Contact Us for Analog IC Pricing →